FTe (Panther Motherboard) Revision 'D' (Rev 1.1.25)
RAM Configuration
Ethernet Options
Disk Drives
Switch Settings
Additional Options
Rear Panel
CMOS Discharge
RAM Configuration
|
Switches |
SIMM Capacity |
Memory Fitted |
1 |
2 |
3 |
Bank 0 |
Bank 1 |
1 MByte |
Off |
Off |
Off |
256k |
- |
1 MByte |
On |
Off |
Off |
256k |
- |
2 MByte |
Off |
On |
Off |
256k |
256k |
4 MByte |
Off |
Off |
On |
1 M |
- |
5 MByte |
On |
On |
Off |
256k |
1 M |
8 MByte |
On |
Off |
On |
1 M |
1 M |
12 MByte |
Off |
On |
On |
2 M |
1 M |
16 MByte |
On |
On |
On |
2 M |
2 M |
Hard Drives
Ethernet Options
| 3Com 32 bit bus master Ethernet card, thin/thick wire (3C527B) |
XB50379 |
| 3Com 16 bit Ethernet card, thin/thick wire (3C523B) |
XB48125 |
| 3Com 16 bit Ethernet card, UTP/thick wire (3C523B-TP) |
XB48127 |
| IBM Token Ring 4/16Mb/s LAN card (25F9528) |
XB49546 |
Switch Settings
SW1
Switch |
On |
Off |
1 |
Cache disable |
Cache enable |
2 |
ROM data on micro channel |
ROM data not on Micro Channel |
3 |
ROM's disabled |
ROM's enabled |
4 |
Refresh enabled |
Refresh disabled |
SW2
Position |
Second Floppy |
A |
5.25" |
B |
3.5" |
SW3
Position |
Second Floppy |
A |
Present |
B |
Not present |
SW4
Switch |
On |
Off |
1 |
RAM configuration |
2 |
RAM configuration |
3 |
RAM configuration |
4 |
CPU speed select |
5 |
CPU speed select |
6 |
FTs |
FTe* |
7 |
Reserved |
Reserved |
8 |
FTe/FTs |
Qi* |
| * When installed in Qi and FTs FE1 must be removed |
| to stop power being supplied on floppy cable |
RAM
| |
Switches |
SIMM Capacity |
Memory Fitted |
1 |
2 |
3 |
Bank 0 |
Bank 1 |
1 MByte |
Off |
Off |
Off |
256k |
- |
1 MByte |
On |
Off |
Off |
256k |
- |
2 MByte |
Off |
On |
Off |
256k |
256k |
4 MByte |
Off |
Off |
On |
1 M |
- |
5 MByte |
On |
On |
Off |
256k |
1 M |
8 MByte |
On |
Off |
On |
1 M |
1 M |
12 MByte |
Off |
On |
On |
2 M |
1 M |
16 MByte |
On |
On |
On |
2 M |
2 M |
Clock speed
CPU speed MHz |
Switches |
| |
4 |
5 |
33 |
Off |
Off |
20 |
On |
Off |
25 |
Off |
On |
Reserved |
On |
On |
SW5
Position |
|
A |
Routes composite sync pulses to the Video DAC |
B |
Composite sync pulses required |
Additional Options
Apricot LOC Technology security.
Co - Processor
486SX 80487SX-25 XB48848
Rear Panel
CMOS Discharge
To remove settings in CMOS the ribbon cable running from the Front Panel
to the I/O Board should be disconnected and then left for approx. 20 minutes.
9595 Main Page
|
