AdapterId 6359h AdapterName "COMTROL RocketPort 8/MC Serial Adapter" Numbytes 4 NamedItem Prompt "IO Address Selection" choice "200-23fh 300-303h" pos[1]=00000011b pos[2]=00000010b IO 0200h-023fh 0300h-0303h choice "300-33fh 400-403h" pos[1]=00000100b pos[2]=00000011b IO 0300h-033fh 0400h-0403h choice "400-43fh 500-503h" pos[1]=00000101b pos[2]=00000100b IO 0400h-043fh 0500h-0503h choice "500-53fh 600-603h" pos[1]=00000110b pos[2]=00000101b IO 0500h-053fh 0600h-0603h choice "600-63fh 700-703h" pos[1]=00000111b pos[2]=00000110b IO 0600h-063fh 0700h-0703h choice "700-73fh 800-803h" pos[1]=00001000b pos[2]=00000111b IO 0700h-073fh 0800h-0803h choice "800-83fh 900-903h" pos[1]=00001001b pos[2]=00001000b IO 0800h-083fh 0900h-0903h choice "900-93fh A00-A03h" pos[1]=00001010b pos[2]=00001001b IO 0900h-093fh 0A00h-0A03h choice "A00-A3fh B00-B03h" pos[1]=00001011b pos[2]=00001010b IO 0A00h-0A3fh 0B00h-0B03h choice "B00-B3fh C00-C03h" pos[1]=00001100b pos[2]=00001011b IO 0B00h-0B3fh 0C00h-0C03h choice "C00-C3fh D00-D03h" pos[1]=00001101b pos[2]=00001100b IO 0C00h-0C3fh 0D00h-0D03h choice "D00-D3fh E00-E03h" pos[1]=00001110b pos[2]=00001101b IO 0D00h-0D3fh 0E00h-0E03h choice "E00-E3fh F00-F03h" pos[1]=00001111b pos[2]=00001110b IO 0E00h-0E3fh 0F00h-0F03h Help "You must choose an IO address for your RocketPort 8/MC. It is possible to have up to four RocketPort 8/MC controllers installed in one system. If multiple controllers are installed, different I/O address ranges must be chosen for each controller. Use the F5=Previous and the F6=Next keys to change the assignment, making sure there is no conflict with another adapter in the system (denoted by an asterisk)." NamedItem Prompt "Interrupt" choice "NONE" pos[3]=00000000b choice "IRQ3" pos[3]=00000011b int 3 choice "IRQ4" pos[3]=00000100b int 4 choice "IRQ5" pos[3]=00000101b int 5 choice "IRQ9" pos[3]=00001001b int 9 choice "IRQ10" pos[3]=00001010b int 10 choice "IRQ11" pos[3]=00001011b int 11 choice "IRQ12" pos[3]=00001100b int 12 choice "IRQ15" pos[3]=00001111b int 15 Help "An interrupt setting for your RocketPort 8/MC is optional depending on the operating system you plan to use. Some operating systems require the use of interrupts and others do not. Please refer to the Device Driver Installation document included with your RocketPort 8/MC for further information on choosing an interrupt setting. Use the F5=Previous and the F6=Next keys to change the assignment. "