@8FEC.ADF IBM ARTIC960 Co-Processor Platform Adapter
C8FEC.ADF Init file for @8FEC.ADF
9mc105.exe ARTIC960 Startup/Option Diskette V1.05
r9mc105.txt ARTIC960 Startup/Option Diskette V1.05 README
193-258 IBM ARTIC960 CO-PROCESSOR PLATFORM
ZG93-0336 IBM ARTIC960 CO-PROCESSOR PLATFORM
194-239 IBM ARTIC960 Coprocessor for IBM RISC System/6000
IBM ARTIC960 Programmable Co-Processors (overview)
ARTIC960 Support for AIX
ARTIC960 Support for AIX Developers Kit
ARTIC960 Support for AIX Supplemental Diskette
ARTIC960 Support for WinNT
ARTIC960 Support for WinNT Developers Kit
ARTIC 960/ARTIC 960PCI Co-Processor Guide to Ops Supplement (thx to Jiri Zlamal)
ARTIC STREAMS Support WAN Driver Interface Reference
ARTIC960 Co-Processor Platforms Hardware Technical Reference
ARTIC960 Programmer's Guide
ARTIC960 Programmer's Reference
ARTIC960 STREAMS Environment Reference
ARTIC960 Co-Processor Platforms Application Interface Board Developer's Guide
RadiSys ARTIC960 Programmer’s Guide (Dec 2000) Covers ARTIC960 PCI / 960Rx / 960Hx / 960RxD / 960 MCA
Realtime Interface Co-Processor C Language Support README
9as122o.txt Installation instr. for IBM ARTIC960 OS/2 ANDIS MAC Device Driver v1.2.2
Cashing in on the ARTIC960
9as122o.exe IBM ARTIC960 OS/2 ANDIS MAC Device Driver Version 1.2.2
9nw101n.exe Netware WAN HSM Installation file for the ARTIC960 PCI adapter
9nw101n.txt Netware WAN HSM Installation instructions for ARTIC960 PCI adapter
9od122o.exe OS/2 Developer's Kit for the ARTIC960 PCI adapter
9od122o.txt OS/2 Developer's Kit Installation for ARTIC960 PCI adapter
9os122o.exe Installation file for the ARTIC960 PCI adapter (OS/2)
9os122o.txt Installation instr. for the ARTIC960 PCI adapter (OS/2)
NOTE: It is conceivable that IBM included support for MCA in some of the driver disks for the 960Hx and Rx PCI ARTICs.
IBM ARTIC Legacy Downloads
qCF SOFTWARE FOR ARTIC
Quadron's qCF is a C-language software development and enhanced runtime support
package for ARTIC cards
ARTIC Portmaster (Quadron site)
If you have any more info on the ARTIC960 or any related AIBs, please
ARTIC960 Base Board P/N 06H4651 FRU 61G2916
J1 140 pin AIB connector
J2 Serial Debug Port ?
J3 Clock Signal Termination
J4 Unk RED / BLACK
U2,4 Micron MT4C16257DJ-7
U6,7 Fujitsu 81C4256A-70 256Kx4
U14 34G1519 Brighton
U18 34G1521 Miami
U25 Packet memory
Y1 40.000 MHz osc MCA Bus
Y2 25.0000 MHz Clock
U1 80960Cx 80960CA 25MHz (initial production) replaced by 80960CF (later production). The CA and CF are register compatible.
U2,4 Instruction memory (DRAM SOJ modules) 1 or 4 MB, 1 to 3 wait states (could be ordered with 4MB!)
SWAG - 4MB version adds U3, U5 Micron MT4C16257DJ-7 ???
U14 34G1519 Brighton Memory Bus controller (plus ECC). Used on i960 boards. (specs)
U18 34G1521 Miami System Bus Interface. Used on i960 boards. (specs)
U19 Pericom P174FCT - Fast CMOS Octal D Flip-Flop with Master Reset (datasheet)
U20 06H3691 EPROM?
U25 72-pin SIMM, 1 (std), 4, 8, or 16 MB (mine had a 1Mx40, ECC, 80 ns SIMM in it.
The LED flashing sequence may be particularly useful for errors that occur
very early on in Preliminary POST, thus preventing notification via the ISP
Register. The No. of Flashes defines a period of consecutive visible flashes
followed by a pause. This pattern is repeated indefinitely.
||Error Source and Description
||No. of Flashes
||Base ROM checksum test failed
||Processor bus test failed
||Local Bus test failed
||Packet memory not detected during boundary test
||Lower 1MB of packet memory failed memory test
||Processor fault occurred
||The SSID is not as expected
What is the purpose of the light on top of the ARTIC card?
The light on the ARTIC card indicates the status of the ARTIC POST routines.
The light normally comes on during POST (power on or reset), and goes off after
successful completion of POST. If the light remains on, an error has been
detected and an error code will be in task 0's secondary status buffer. A
flashing light indicates a memory error on the card (since the error code can
not be reported via memory).
One other difference in reset between Micro Channel and PCI systems is that
Ctrl+Alt+Del does not reset adapters in PCI systems.
J3 Clock Signal on ARTIC960 Co-Processor Platform (Micro Channel)
The ARTIC960 supplies a clock signal (25MHz) to the AIB. This signal must be
terminated at all times. Normally, the AIB circuitry terminates this signal. The
ARTIC960 has a three-pin jumper (J3), which provides an on-card
resistance-capacitance (RC) termination for the clock. If you do not have an AIB
installed, J3 is jumpered 2-3 to terminate the clock signal on the ARTIC960.
When an AIB is installed, J3 is jumpered 1-2, which is a "no-connect" position
for the on-card termination circuitry, and allows the termination to take place
using the AIB circuitry.
Note: On this ARTIC960
with an installed AIB, J3 was jumpered for 3-2, which is
supposedly for Termination. Possibly not correct...
Warning! Damage to the Memory Controller Chip and/or the Micro Channel Interface Chip could occur if the termination is not used when the co-processor is powered up without an AIB attached.
6 Port V.36 AIB FRU 11H3795 (52G0985?)
J1 100-pin header
J2 140-pin AIB connector
JP1 Two solder pads
U1, 2 34G1522 VERO AIB/DMA
U4, 6, 7, 8, 13, 14 DS36950V
U9, 11, 91 SC26C562C1A
Y1 12.2880 MHz osc
Y2 14.7456 MHz osc (DUSCC clock)
U1, 2 34G1522 VERO
AIB/DMA - CFE Local Bus/AIB Interface Chip Vero Datasheet
superseded by the VOLANT chip on ARTIC960 PCI AIBs. Volant Datasheet
Dual universal serial communications controller (DUSCC) Datasheet
Differential Bus Transceiver Datasheet
lT1141A - Advanced Low
Power 5V RS232 Drivers/Receivers with Small Capacitors Datasheet
# 6930 ... ARTIC 960 Adapter 61G2925
# 6933 ... 4 MB memory
# 6934 ... 8 MB memory
# 6940 ... Application Interface Board, 4-port Selectable 61G2960 / 61G2961 4-port Multi-interface Aib
High-speed 4-Port Multi-interface AIB that offers either EIA-232, EIA-530 (RS-422), ISO 4903
(X.21), or ISO 4902 (V.36) electrical interfaces for
generalized applications. The
selection of the specific interface is achieved by
a matching cable (four ports of either 232, 422, X.21, or V.36)
# 6941 ... cable, 4-port EIA-232 61G2918
# 6932 ... cable, 4-port EIA-530 / EIA-422 61G2923
# 6943 ... cable, 4-port X.21 61G2928
# 6944 ... cable, 4-port V.36 61G2933
- At least four to six times the performance
of Portmaster Adapter/A. The 4-Port Multi-interface
Application Interface Board handles four lines of
communications data at 2.048 megabits per second.
- Intel (1) 80960ca 25-MHz processor
- Support for DMA 32-bit bus master and
peer-to-peer capability on the Micro Channel
- 64-bit streaming data (80MB/s) capability
- From 2 to 17MB of memory (capability
of 1 to 20MB through an RPQ)
- Architected to accept a 32MB single
in-line memory module (SIMM)
- System Control Block (SCB) Move-mode
For the '94 RS/6000 versions, memory supported has
dropped to the 1, 4, or 8MB SIMM.
- From 2 to 9MB of memory (additional memory
available via an RPQ)
Included in this announcement is a high-speed 4-Port
multi-interface Application Interface Board (AIB). The
AIB offers either EIA-232D (asynchronous), or EIA-530
(RS422), or ISO 4903 (X.21) or ISO 4902 (V.36)
electrical interfaces for communications applications.
The selection of the specific interface is achieved by a
matching cable (4 ports of 232 or 4 ports of 422 or 4
ports of X.21 or 4 ports of V.36).
The application development driver is intended to
provide a level of interface to the adapter for those
developing applications using the ARTIC960 and is not a
full-function driver. The application development driver
is contained in the diagnostic diskette.
A developer's kit is offered that provides AIB design
information, sample programs, a programmer's
guide/reference, and a hardware technical reference
manual. As part of the developer's kit a Developer's
Assistance Program (DAP) is provided for parties who will
be developing their own software applications and/or
designing their own application interface board. The
The ARTIC960 adapter requires a 32-bit slot in the
following Micro Channel machines
There is no limitation on the quantity of ARTIC960 cards
per system other than 32-bit Micro Channel long slot
availability and the amount of power furnished by the
system. A typical ARTIC960 adapter, without the AIB, draws
12.5 watts of 5VDC power. The Multi-interface AIB draws an
additional 3.7 watts.
There is a limitation of 5 IBM ARTIC960
coprocessor with the supplied driver in all models except
Machine Type 7009 Model C10 which has a limit of 2.
The adapter is designed with two memory
banks. The instruction memory is 1MB large and is soldered
in place. The other memory bank or data memory (also
referred to as "packet") is provided in the form of a
selectable pluggable SIMM package. The SIMM sizes are 1,
4, 8, and 16MB, with the card designed to accept a 32MB
SIMM. A SIMM must be installed for the ARTIC960 to
Note: I have an
ARTIC960 with a 6 port V.36 AIB, and the SIMM is a 4M ECC
SIMM. 68X6356 1Mx40 E 80 ns, 5 V
@8FECH ARTIC960 Co-Processor Platform Adapter
Modify the ADF file so that all features are "disabled"
and remove the ability to disable channel check sources.
Channel check sources is always enabled. Change Advanced
Co-Processor Platform Adapter to ARTIC960 Co-Processor
Device I/O Address
Six-bit field that
selects the I/O address of the ARTIC960 Adapter. The six bits represent bits 15 through
10 of the I/O address. Address bits 15, 14, and 13 are in
POS register 5. Address bits 12, 11, and 10 are in POS
subaddress 100 (POS register 3A).
3C00-3C1F, 5C00-5C1F, 7C00-7C1F, 9C00-9C1F, BC00-BC1F,
interrupt request line on which the ARTIC960 Adapter interrupts the system. The highest to
lowest interrupt priorities are as follows: 9, 10, 14, 7.
The interrupt level may be shared with another adapter.
The preferred interrupt level is 7.
7">, 10, 14, 9
Primary Arbitration Level
Primary arbitration level
for the ARTIC960 Adapter Busmaster
DMA transfers. Arbitration level of 0 has highest
priority, and increasing levels have corresponding
E">, D, C, B, A, 9, 8, 3, 2, 1
Enable or disable Streaming
Data feature of the ARTIC960 Adapter
as both a Bus Master and a Slave. Default is disable, which causes the adapter to use the
basic data transfer procedures. When enabled, the
streaming data procedure is supported.
Selected Feedback Return
Enable or disable checking
and reporting of loss of Selected Feedback Return by the
ARTIC960 Adapter Bus Master. Default is disable.
Address and Data Parity
Enable or disable address
and data parity checking / generation by the ARTIC960 Adapter. The default is disable.
Mode that the
ARTIC960 Adapter uses when driving
-CHCK active. When synchronous mode is
selected, -CHCK is signaled by the adapter with a pulse on
-CHCK during the data transfer cycles. When selected for
asynchronous mode, the adapter drives -CHCK active
asyschronously to a data transfer, i.e -CHCK remains
active until reset by the system master. Default is Asynchronous.
1st Shared Storage Window
There are two independent windows into the
RAM on the ARTIC960 Adapter. The first window is located in the ROM/RAM area. The window can be either 8 KBytes or 16 KBytes
<"DE000H-DFFFFH, 8K Window">, DC000-DDFFF,
DA000-DBFFF, D8000-D9FFF, D6000-D7FFF, D4000-D5FFF,
D2000-D3FFF, D0000-D1FFF, CE000-CFFFF, CC000-CDFFF,
CA000-CBFFF, C8000-C9FFF, C6000-C7FFF, C4000-C5FFF,
16K Window">, D8000-DBFFF, D4000-D7FFF,
D0000-D3FFF, CC000-CFFFF, C8000-CBFFF,
2nd Shared Storage Window Location (This field will
call the ADP)
There are two independent windows into the
RAM on the ARTIC960 Adapter. The second window is located above
1 MEG. The size of this window is equal to the amount of
RAM installed on the adapter