AdapterId 06E79h AdapterName "IRMA 3 3270 Coax Adapter" NumBytes 4 NamedItem Prompt "IRMA 3 Adapter Address" choice "200h-20Fh" pos[0]=0000000xb io 0200h-020Fh choice "240h-24Fh" pos[0]=0001000xb io 0240h-024Fh choice "260h-26Fh" pos[0]=0001100xb io 0260h-026Fh choice "2E0h-2EFh" pos[0]=0011100xb io 02E0h-02EFh Help "This is the IRMA 3 adapter address. Four choices are available : 200h - 20Fh 240h - 24Fh 260h - 26Fh 2E0h - 2EFh" NamedItem Prompt "IBM Emulator Port Address" Choice "Fixed Resource" pos[0]=xxxxxxxxb pos[1]=xx111000b pos[2]=xxxxxx01b io 02D0h - 02DFh int 2 Choice "Disable IBM" pos[0]=xxxxxxxxb pos[2]=xxxxxxx0b Help "The IBM emulator port Address is fixed at 02D0h - 02DFh and uses interrupt 2 and dual port memory at 0CE000 - 0CFFFFh. If these resources conflict with another adapter board in the PC you can: 1. Change the resource requirements on the other board to resolve the conflict or 2. Choose 'Disable IBM'. You can not run IBM emulation software on IRMA 3 if IBM is disabled." NamedItem Prompt "IRMA Emulator Port Address" Choice "Enable 220-227" pos[0] = xxxxxxxxb pos[1]=1xxxxxxxb io 0220h-0227h Choice "Disable 220-227" pos[0]=xxxxxxxxb pos[1] = 0xxxxxxxb Help "The IRMA Emulator port Address is fixed at 220h. If the IRMA Emulator Port address conflicts with another adapter board in the PC you can: 1. Change the port address setting on the other board to resolve the conflict or 2. Choose 'Disable 220 - 227'. Older DCA emulation software, such as E78, and applications written for the original PROM board IRMA product only run at address 220 - 227. If your software requires this address 'Enable 220 - 227' must be selected. Current DCA emulators, i.e. E78 PLUS, Irmax - Multisession and Irmax - DFT, can be configured to use the three DCA emulator addresses selected below." NamedItem Prompt "IRQ levels and disable interrupt" choice "IRQ9 " pos[1]=xxx11000b int 9 choice "IRQ10" pos[1]=xxx11001b int 10 choice "Disable INT" pos[1]=xxx0xxxxb Help "When using IBM emulation software or DCA Irmax - DFT or Irmax - Multisessions, IRQ9 (same as IRQ2) must be selected." NamedItem Prompt "DCA Emulator Address" choice "280h-29Fh" pos[1]=x1xxxxxxb pos[2]=100xxxxxb io 0280h-029Fh choice "2A0h-2BFh" pos[1]=x1xxxxxxb pos[2]=101xxxxxb io 02A0h-02BFh choice "2C0h-2DFh" pos[1]=x1xxxxxxb pos[2]=110xxxxxb io 02C0h-02DFh choice "Disable DCA" pos[1]=x0xxxxxxb Help "Address 280 - 29F is the recommended setting for use with DCA emulators. If the DCA Emulator Address conflicts with another adapter board in the PC you can : 1. Change the port address setting on the other board to resolve the conflict or 2. Choose one of the two alternate addresses and configure the DCA emulator to use the new address." NamedItem Prompt "RAM Address Range" choice "CE000 - CFFFF" pos[1]=xx1xxxxxb pos[3]=xx011100b MEM 0CE000h - 0CFFFFh choice "Disable RAM" pos[1]=xx0xxxxxb pos[3]=xx0000xxb Help "When using IBM emulation software Ram Address Range CE000 - CFFFF must be selected. If the Ram Address Range conflicts with another adapter in the PC you can : 1. Change the ram address setting on the other board to resolve the conflict or 2. Choose 'Disable Ram'. You can not run IBM emulation software on IRMA 3 if disable ram is selected."