AdapterId 0500h AdapterName "CORE CNT-MCK Fixed Disk Adapter" NumBytes 4 fixedresources pos[0]=100XXXXXb pos[2]=XXXX11XXb ;;; always sample CHRDYRTN pos[3]=000X1111b nameditem Prompt "I/O Port Address" Choice "0800h-080Fh" pos[1]=X0000XXXb io 0800h-080fh Choice "0840h-084Fh" pos[1]=X0001XXXb io 0840h-084fh Choice "0880h-088Fh" pos[1]=X0010XXXb io 0880h-088fh Choice "08C0h-08CFh" pos[1]=X0011XXXb io 08C0h-08cfh Choice "0900h-090Fh" pos[1]=X0100XXXb io 0900h-090fh Choice "0940h-094Fh" pos[1]=X0101XXXb io 0940h-094fh Choice "0980h-098Fh" pos[1]=X0110XXXb io 0980h-098fh Choice "09C0h-09CFh" pos[1]=X0111XXXb io 09C0h-09Cfh Choice "0A00h-0A0Fh" pos[1]=X1000XXXb io 0a00h-0a0fh Choice "0A40h-0A4Fh" pos[1]=X1001XXXb io 0a40h-0a4fh Choice "0A80h-0A8Fh" pos[1]=X1010XXXb io 0a80h-0a8fh Choice "0AC0h-0ACFh" pos[1]=X1011XXXb io 0ac0h-0acfh Choice "0B00h-0B0Fh" pos[1]=X1100XXXb io 0b00h-0b0fh Choice "0B40h-0B4Fh" pos[1]=X1101XXXb io 0b40h-0b4fh Choice "0B80h-0B8Fh" pos[1]=X1110XXXb io 0b80h-0b8fh Choice "0BC0h-0BCFh" pos[1]=X1111XXXb io 0bc0h-0bcfh Help "This option selects the I/O port address range for the adapter. Under normal circumstances, select <0800h-080Fh>." nameditem Prompt "BIOS Memory Address" Choice "D8000-DBFFFh" pos[1]=XXXXX110b mem 0d8000h-0dbfffh Choice "ROM Disabled" pos[1]=XXXXX000b Choice "DC000-DFFFFh, Int 19 load" pos[1]=XXXXX111b mem 0dc000h-0dffffh Choice "C8000-CBFFFh" pos[1]=XXXXX010b mem 0c8000h-0cbfffh Choice "CC000-CFFFFh" pos[1]=XXXXX011b mem 0cc000h-0cffffh Choice "D0000-D3FFFh" pos[1]=XXXXX100b mem 0d0000h-0d3fffh Choice "D4000-D7FFFh" pos[1]=XXXXX101b mem 0d4000h-0d7fffh Help "This option selects the memory address for the on-card BIOS ROMs. The BIOS ROM should be enabled on only one CNT-MCK controller in the system. Also, the BIOS ROM address selected should be higher than that of any other fixed disk controller which may be in the system. Under normal circumstances, select ." nameditem Prompt "DMA Arbitration Level" Choice "Level 5" pos[0]=XXX0101Xb arb 5 Choice "Level 6" pos[0]=XXX0110Xb arb 6 Choice "Level 7" pos[0]=XXX0111Xb arb 7 Choice "Level 0" pos[0]=XXX0000Xb arb 0 Choice "Level 1" pos[0]=XXX0001Xb arb 1 Choice "Level 3" pos[0]=XXX0011Xb arb 3 Choice "Level 4" pos[0]=XXX0100Xb arb 4 Choice "Level 8" pos[0]=XXX1000Xb arb 8 Choice "Level 9" pos[0]=XXX1001Xb arb 9 Choice "Level 0A" pos[0]=XXX1010Xb arb 0ah Choice "Level 0B" pos[0]=XXX1011Xb arb 0bh Choice "Level 0C" pos[0]=XXX1100Xb arb 0ch Choice "Level 0D" pos[0]=XXX1101Xb arb 0dh Choice "Level 0E" pos[0]=XXX1110Xb arb 0eh Help "This selects the Arbitration level that the controller will use when competing for the bus. A lower arbitration level gives a controller a higher priority when competing for the bus." nameditem Prompt "Fairness On/Off" Choice "On" pos[3]=XXX1XXXXb Choice "Off" pos[3]=XXX0XXXXb Help "This option controls whether the adapter will release control of the bus when it has been using it exclusively. Under normal circumstances, select ." nameditem Prompt "Minimum Burst Length" Choice "8 Word" pos[2]=XX10XXXXb Choice "4 Word" pos[2]=XX01XXXXb Choice "1 Word" pos[2]=XX00XXXXb ;;; Choice "12 Word" pos[2]=XX11XXXXb Help "This option controls the minimum number of 16-bit data words that will be transferred between the controller and memory at a time. Preempt requests from other controllers (or memory refresh) will only be recognized between bursts of the chosen length. Normally, select <8 Word>. Smaller lengths should only be used if a very slow memory board is installed. If an AOX Micromaster board is installed, select <4 Word>." ;;;nameditem ;;; Prompt "Wait states" ;;; Choice "Sample CHRDYRTN" pos[2]=XXXX11XXb ;;; Choice "1 Wait State" pos[2]=XXXX10XXb ;;; Choice "0 Wait States" pos[2]=XXXX00XXb ;;; ;;; Help ;;; "This option controls whether Channel Ready will be sampled when ;;; memory is accessed. ;;; Wait states can only be disabled on systems having ZERO wait state ;;; memory, like the IBM model 50Z. ;;; Clock speed and wait states both affect the length of time required ;;; to transfer each word of data. ;;; For normal operation, use ." nameditem Prompt "Disk Controller Clock Speed" Choice "High" pos[1]=0XXXXXXXb Choice "Low" pos[1]=1XXXXXXXb Help "This option controls the speed of the clock that the disk controller uses (20MHz or 14.3MHz) when performing transfers to/from the system bus. Clock speed and wait states both affect the length of time required to transfer each word of data. Normally, select ."